What is the use of IC 8038?
8038 IC – Function Generator IC. The 8038 waveform generator is a monolithic integrated circuit capable of producing high accuracy sine, square, triangular, saw tooth and pulse wave forms with a minimum of external components.
Why IC 8038 is called function generator?
The ICL8038 is a function generator chip, capable of generating triangular, square , sine, pulse and sawtooth waveforms . From these sine, square & triangular wave forms can be made simultaneously. There is an option to control the parameters like frequency,duty cycle and distortion of these functions.
Is IC 8038 a voltage controlled oscillator?
ICL8038 was a voltage-controlled oscillator capable of producing frequencies between a millihertz and 100 kHz., some specimens capable of reaching 300 kHz. The device has been discontinued by Intersil in 2002. The output frequency was set either by resistors or the external control voltage.
What type of wave from is available at PIN number 2 of function generator IC 8038?
Pin description: Pin 2 Sine Wave Output: Sine wave output is available at this pin. The amplitude of this sine wave is 0.22 Vcc.
What is function generator IC?
A function generator is usually a piece of electronic test equipment or software used to generate different types of electrical waveforms over a wide range of frequencies. Integrated circuits used to generate waveforms may also be described as function generator ICs.
Which pin is used for output in IC 566?
FEATURES of 566 VCO: 566 VCO is an 8 pin IC, it can operate between 10 to 24 volts. High linearity of modulation. stable center frequency. Highly linear triangle wave output.
What is IC 565?
IC 565 is the most commonly used phase locked loop IC. It is a 14 pin Dual-Inline Package (DIP). The pin diagram of IC 565 is shown in the following figure − The purpose of each pin is self-explanatory from the above diagram. Out of 14 pins, only 10 pins (pin number 1 to 10) are utilized for the operation of PLL.
What is the difference between a signal generator and a function generator?
Signal generators make available at their outputs sinusoidal waveforms with a settable frequency or amplitude. Function generators go beyond signal generators in that they allow the generation of periodic standard functions such as sine, square, triangle, ramp up/down, dc, and noise.
How do you make an RF signal?
There are two main techniques that are used within synthesized RF signal generators: Phase locked loop synthesizer: Phase locked loop synthesizers are used within most RF signal generators as they enable signals to be generated over a wide range of frequencies with a relatively low level of spurious signals.
What is VCO frequency?
A voltage-controlled oscillator (VCO) is an electronic oscillator whose oscillation frequency is controlled by a voltage input. The applied input voltage determines the instantaneous oscillation frequency. A VCO is also an integral part of a phase-locked loop.
Which IC is used as PLL?
Introduction to PLL In present, the PLL is available as a single IC in the SE/NE560 series (560, 561, 562, 564, 565 and 567) to further reduce the buying cost ,the discrete IC’s are used to construct a PLL.
Is a PLL IC?
Phase Locked Loop (PLL) is one of the vital blocks in linear systems. It is useful in communication systems such as radars, satellites, FMs, etc.
What kind of signal can the ICL8038 generate?
The ICL8038 is a function generator chip that can generate three basic signals such as Sine, Square and triangle waveforms. The IC has also provided room to adjust the important parameters of a waveform such as Frequency and duty cycle. The frequency of the signal can be modified from 0.001KHz to 300KHz using external resistors and capacitors.
Can a function generator IC be used as a waveform generator?
Integrated circuits used to generate waveforms may also be described as function generator ICs. ICL8038 is a waveform generator. Here is the functional block diagram of this IC. Yes, there are similar ICs which can be used as function generator. You can use XR2206 IC too to generate different waveform.
How is the repetition rate of an IC generator selected?
The frequency (or repetition rate) can be selected externally from 0.001Hz to more than 300kHz using either resistors or capacitors, and frequency modulation and sweeping can be accomplished with an external voltage.
Can a function generator be connected to a 60mhz counter?
Output of 1Hz – 2MHz XR2206 Function Generator can be connected directly to 60MHz Counter for setting precise frequency output. Be “On Air” with your own radio station!