How do I log into my NanoStation M5?

To get access to your Ubiquiti NanoStation-M5, you need the IP of your device, the username and password….Ubiquiti NanoStation-M5 Login Guide

  1. Open your web browser (e.g. Chrome, Firefox, Opera or any other browser)
  2. Type 192.168.
  3. The default username for your Ubiquiti NanoStation-M5 is ubnt.

What is the default username and password for Ubiquiti router?

ubnt
The default username is ubnt and the default password is ubnt.

How do I reset my NanoStation M5?

Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the NanoStation is powered on. Alternatively, a remote reset button is located on the bottom of the PoE Adapter. * Main is labeled LAN on the NanoStationlocoM2/M5. 1.

How do I access my NanoStation?

Open your browser (e.g. Internet Explorer, Firefox, Opera, etc.) and type in address bar: http://192.168.1.20 (the default address of the Nano) then press the Enter key. Type in ubnt twice and click OK → (If this window did not appear, there may be a problem with the wiring, the network card or a firewall).

How do I reset my Litebeam M5?

Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. The device may also be reset remotely using the auxiliary Reset button located on the bottom of the PoE Adapter.

What is Nano M5?

The Ubiquiti NanoStation M5 (NSM5) is a high performance, low cost and extremely versatile Point-to-Point wireless bridge. The NSM5 comes with a redesigned, sleek and elegant form-factor, along with integrated Ubiquiti airMax (MIMO TDMA Protocol) technology.

How do I find my UniFi username and password?

Your username is your email address you use to register unifi service. If you happen to forget your username or password, click on the ‘Forgot Email’ or ‘Forgot Password’ respectively in the Self-Care page. ‘Forgot Password’ – Enter your Email address (We will send the password to your email address.)

What is ubnt default password?

As long as the UniFi Access Point has not been previously setup or adopted by the software, and only if you are attempting to connect via SSH, then always use the default username and password of ubnt / ubnt.

What is the use of NanoStation M5?

The Ubiquiti NanoStation M5 provides a secondary Ethernet port with software enabled PoE output for seamless IP Video integration. Remote hardware reset circuitry of Ubiquiti NanoStation M5 allows for device to be reset remotely from power supply location.

What is the default username for The Nanostation M5 router?

The Default Ubiquiti NanoStation M5 Router Username is: blank. The Default Ubiquiti NanoStation M5 Router Password is: blank. Enter your username and password, and then click the Login button to log in to your Ubiquiti NanoStation_M5 router.

What is the frequency of The Nanostation M5?

not present Model O Operating Frequency E Ethernet Ports N NanoStation M5 5 5170-5875 MHz* 2 2 N NanoStation Loco M2 2 2402-2482 MHz N NanoStation Loco M5 5 5170-5875 MHz* N NanoStation Loco M900 9 904-926 MHz

Where do I enter my UBNT for nanostationm?

Make sure that your host system is connected via Ethernet to the device. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. Launch your web browser and type https://192.168.1.20 in the address field. Press enter (PC) or return (Mac). Enter ubnt in the Username and Password fields.

How do I set up my Nanostation 2?

Setting up the Nano • Open your browser (e.g. Internet Explorer, Firefox, Opera, etc.) and type in address bar: http://192.168.1.20 (the default address of the Nano) then press the Enter key. • Type in ubnt twice and click OK → (If this window did not appear, there may be a problem with the wiring, the network card or a firewall).

Share this post